ThinkSystem 430-x PCIe 12Gb HBA Driver for Windows 2025

Supported Controllers:
    ThinkSystem 1611-8p NVMe Switch Card
			
NOTE TO SERVICE - Reference RETAIN #N/A

Version 2.61.72.00
------------------

Defects:
-Expander FW initialization code dereferences null pointer after null check.(DCSG00421214 (Port Of Defect DCSG00415838))
-SDK does not recover the PHY when the SPICO_ECC fault (0x175) is reported.(DCSG00507124 (Port Of Defect DCSG00411475))
-Watchdog Status sometimes doesn't show valid Reset Status value for Expander soft reset.(DCSG00507130 (Port Of Defect DCSG00501521))
-Partial Error Log Header Causes Firmware Fault.(DCSG00106334)
-Multi master I2C communication within 2 expanders using I2C packet layer fails on one expander reset..(DCSG00110208)
-I2C communication within 2 expanders using I2C packet layer fails on one expander reset.(DCSG00112595)
-If the amount of information requested exceeds the size of the config page, Exp FW terminates the command with CHECK CONDITION status for buffer ID 0xE6>(DCSG00205352)
- Add note in Exp XML 'Spinup Control Configuration Page (0xFF0A) and prog guide that Exp 'spin-up' and 'phy reset in progress timeout' setting should be in sync>(DCSG00218728)
-The SAS35Xnn expander is unresponsive to CLI or in-band interfaces during stress testing with watchdog and phy resets.(DCSG00219838)
-Expander may exhibit issue if multiple hosts try to do config page read/write operations concurrently.(DCSG00226514)
-When in-place concatenated image is active, log shows that the MFG image is unreadable.(DCSG00234564)
-Executing rapid phy resets causes expanders to exhibit inappropriate behavior.(DCSG00242358) 
-I2C master fails to communicate with peer expander I2C slave with master power cycles test.(DCSG00242592)
-Assert observed in ISTWI Slave module in a stress test involving peer master power cycle.(DCSG00243797)
-NULL pointer could have been de-referenced for reading while tracing firmware flow in the API that creates the transaction context for SSPI>(DCSG00249050)
-Expander FW does not set warning/critical field even though Voltage sensor element reports critical status.(DCSG00253035) 
-Write Buffer command with size/offset beyond the allowed buffer size give incorrect response.(DCSG00253043)
-Remove unnecessary #include "../include/aapl/aapl.h" from halPhyConfiguration.c.(DCSG00257751)
-When 0.15.203.00 version of expander FW is active on CubR boards, Scrutiny CLI's 'show' command doesn't complete.(DCSG00264968)
- Compilation failure seen while creating in-place concatenated image.(DCSG00266712)
-Config page write using buffer ID 0xE6 failed.(DCSG00394079)
-Unsupported vendor specific commands return INVALID FIELD IN CDB as the sense code.(DCSG00118485 (Port Of Defect DCSG00103403))
-INVALID COMMAND OPERATION CODE is returned as Additional Sense Code for unsupported SES Page.(DCSG00119142 (Port Of Defect DCSG00103326))
- Fault in halSspIisr.c.(DCSG00143502 (Port Of Defect DCSG00093790))
-Update from Pre-Phase 9.0 fw to Phase 9.0 or later results in 0x175 Fault.(DCSG00153880 (Port Of Defect DCSG00132832))
-Watchdog reset is seen with Peak Value Detection configured for Databolt enabled PHYs.(DCSG00304554 (Port Of Defect DCSG00259162))

Enhancements：
-Support for 930-24i controller on SR650 V2 platform.(DCSG01825526)
-Add Tx FIFO flush logic to the ISTWI master arbitration lost handler.(DCSG00778893)
-Add note in expander config XML and programming guide that expander 'spin-up' and 'phy reset in progress timeout' MFG config setting should be in sync.(DCSG00164169)
-Upgrade Vero-24i code base to Cub PH16 SDK equivalent.(DCSG00433512)


Version 2.61.68.00
------------------

Defects:
-Invalid Interrupt coalescing control values need to be initialized..(DCSG01562385)
-Orphaned IOCTL handling in Windows Driver watchdog timer is not synchronized.(DCSG01548841)
-Windows driver is not logging events to event viewer when the adapter is gone from the sytem.(DCSG01545048)
-The RT trace logged for mapping table size in Find Adapter does not record the RT trace.(DCSG01532243)
-Source build fails with the python build tools.(DCSG01598304)
-
nhancements:
-IO path Optimization.(DCSG01548995)
-Remove unused global variables from the itsas35 driver device Extension.(DCSG01531658)
-New OS Windows 11 23H2 Client Support addition.(DCSG01587975)
-PnP ID update for OEMs.(DCSG01588518)


Version 2.61.35.00
------------------
Initial release